中文名称: Telotristat
英文名称: Telotristat
CAS No: 1033805-28-5
分子式: C25H22ClF3N6O3
分子量: 546.93
T70769 Telotristat ≥99% (psaitong)
沸点:
731.1±70.0 °C(Predicted)
密度:
1.50±0.1 g/cm3(Predicted)
包装规格:
2mg 5mg in glass bottle
产品简介:
一种有效的色氨酸羟化酶 (tryptophan hydroxylase) 抑制剂,在体内的 IC50 值为0.028 μM。
溶解性:
不溶于 H2O,不溶于乙醇
储备液保存:
-80°C, 2 years
-20°C, 1 year
体内实验:
1、请依序添加每种溶剂:10% DMSO→40% PEG300→5% Tween-80→45% Saline
Solubility: ≥ 2.5 mg/mL (4.57 mM); 澄清溶液
此方案可获得 ≥ 2.5 mg/mL(饱和度未知)的澄清溶液。
以 1 mL 工作液为例,取 100 μL 25.0 mg/mL 的澄清 DMSO 储备液加到 400 μL PEG300 中,混合均匀;再向上述体系中加入 50 μL Tween-80,混合均匀;然后再继续加入 450 μL 生理盐水 定容至 1 mL。
2、请依序添加每种溶剂:10% DMSO→90% (20% SBE-β-CD in Saline)
Solubility: ≥ 2.5 mg/mL (4.57 mM); 澄清溶液
此方案可获得 ≥ 2.5 mg/mL(饱和度未知)的澄清溶液。
以 1 mL 工作液为例,取 100 μL 25.0 mg/mL 的澄清 DMSO 储备液加到 900 μL 20% 的 SBE-β-CD 生理盐水水溶液 中,混合均匀。
3、请依序添加每种溶剂:10% DMSO→90% Corn Oil
Solubility: ≥ 2.5 mg/mL (4.57 mM); 澄清溶液
此方案可获得 ≥ 2.5 mg/mL(饱和度未知)的澄清溶液,此方案实验周期在半个月以上的动物实验酌情使用。
以 1 mL 工作液为例,取 100 μL 25.0 mg/mL 的澄清 DMSO 储备液加到 900 μL玉米油中,混合均匀。

<1mg/ml表示微溶或不溶。
普西唐提供的所有化合物浓度为内部测试所得,实际溶液度可能与公布值有所偏差,属于正常的批间细微差异现象。
请根据产品在不同溶剂中的溶解度选择合适的溶剂配制储备液;⼀旦配成溶液,请分装保存,避免反复冻融造成的产品失效。
靶点:
IC50: 0.028 μM (tryptophan hydroxylase)
体外研究:
Telotristat is the active moiety of telotristat etiprate. Telotristat etiprate is an ethyl ester prodrug which is hydrolyzed to telotristat. Telotristat etiprate is orally available serotonin synthesis inhibitor for the treatment of carcinoid syndrome.
体内研究:
Telotristat etiprate is present in very low levels after oral administration. These low levels are due to rapid hydrolysis into the active moiety telotristat. The half-life ranges from approximately 4-12 h. There is no accumulation of telotristat with multiple dose administration over 2 weeks. Exposure to telotristat is approximately dose proportional.
注意事项:
1、为了您的安全和健康,请穿实验服并戴一次性手套操作。
2、以上信息仅做参考交流之用。
保存条件:
2-8°C
UN码:
HazardClass:
危害声明:
安全说明:
搜索质检报告(COA)
参考文献 & 客户发表文献

本计算器可帮助您计算出特定溶液中溶质的质量、溶液浓度和体积之间的关系,公式为:
质量 (g) = 浓度 (mol/L) x 体积 (L) x 分子量 (g/mol)

摩尔浓度计算公式

  • =
    *
    *
    *选择对应的单位 *空出希望得到的变量,填写另外两个变量

用本工具协助配置特定浓度的溶液,使用的计算公式为:
开始浓度 x 开始体积 = 最终浓度 x 最终体积

稀释公式

稀释公式一般简略地表示为:C1V1 = C2V2 ( 输入 输出 )

  • * = *

连续稀释计算器方程

  • 连续稀释

  • 初始浓度:
  • 稀释倍数:
  • 计算结果

  • C1=C0/X C1: LOG(C1):
    C2=C1/X C2: LOG(C2):
    C3=C2/X C3: LOG(C3):
    C4=C3/X C4: LOG(C4):
    C5=C4/X C5: LOG(C5):
    C6=C5/X C6: LOG(C6):
    C7=C6/X C7: LOG(C7):
    C8=C7/X C8: LOG(C8):