中文名称: | (S)-特拉唑嗪 | ||||
---|---|---|---|---|---|
英文名称: | (S)-Terazosin | ||||
别名: | (S)-特拉唑嗪 (S)-Terazosin | ||||
CAS No: | 109351-33-9 | 分子式: | C19H25N5O4 | 分子量: | 387.43 |
CAS No: | 109351-33-9 | ||||
分子式: | C19H25N5O4 | ||||
分子量: | 387.43 |
基本信息
产品编号: |
T10830 |
||||
产品名称: |
(S)-Terazosin |
||||
CAS: |
109351-33-9 |
储存条件 |
粉末 |
-20℃ |
四年 |
|
|
||||
分子式: |
溶于液体 |
-80℃ |
6个月 |
||
分子量 |
387.43 |
-20℃ |
1个月 |
||
化学名: |
(S)-(4-(4-Amino-6,7-dimethoxyquinazolin-2-yl)piperazin-1-yl)(tetrahydrofuran-2-yl)methanone |
||||
Solubility (25°C): |
|||||
体外:
|
DMSO |
|
|||
Ethanol |
|
||||
Water |
|
||||
体内(现配现用): |
|
||||
<1mg/ml表示微溶或不溶。 |
|||||
普西唐提供的所有化合物浓度为内部测试所得,实际溶液度可能与公布值有所偏差,属于正常的批间细微差异现象。 |
|||||
请根据产品在不同溶剂中的溶解度选择合适的溶剂配制储备液;⼀旦配成溶液,请分装保存,避免反复冻融造成的产品失效。 |
制备储备液
浓度
溶液体积 质量 |
1mg |
5mg |
10mg |
1mM |
2.5811mL |
12.9056mL |
25.8111mL |
5mM |
0.5162mL |
2.5811mL |
5.1622mL |
10mM |
0.2581mL |
1.2906mL |
2.5811mL |
生物活性
产品描述 |
Terazosin 的有活性的 S 型异构体,也是一种有效的,高亲和力的 α-肾上腺素受体拮抗剂,对 α1a,α1b 和 α1d-肾上腺素受体的 Ki 值分别为 3.91nM,0.79nM 和 1.16nM。(S)-Terazosin 对 α2a,α2B 和 α2c-肾上腺素受体也具有高亲和力,Ki 值分别为 729nM,3.5nM 和 46.4nM。 |
靶点 |
Ki:3.91nM (α1a-adrenoceptor),0.79nM (α1b-adrenoceptor) and 1.16nM (α1d-adrenoceptor);729nM (α2a-adrenoceptor),3.5nM (α2Ba-adrenoceptor) and 46.4nM (α2c-adrenoceptor). |
体外研究 |
The racemic compound and its enantiomers show high and apparently equal affinity for subtypes of α1-adrenoceptors with Ki values in the low nanomolar range,and showed potent antagonism of α1-adrenoceptors in isolated tissues,with the enantiomers approximately equipotent to the racemate at each α1-adrenoceptor subtype.At α2b sites,(R)-Terazosin binds less potently than either the (S)-Terazosin or racemate. |
体内研究 |
(S)-Terazosin shows antagonism of at rat atrial α2B receptor with a pEC30 of 6.93.(s)-Terazosin shows antagonism of at rat vas deferens α1A and α2A receptor with pA2 values of 8.3 and 6.12,respectively. |
本计算器可帮助您计算出特定溶液中溶质的质量、溶液浓度和体积之间的关系,公式为:
质量 (g) = 浓度 (mol/L) x 体积 (L) x 分子量 (g/mol)
摩尔浓度计算公式
用本工具协助配置特定浓度的溶液,使用的计算公式为:
开始浓度 x 开始体积 = 最终浓度 x 最终体积
稀释公式
稀释公式一般简略地表示为:C1V1 = C2V2 ( 输入 输出 )